Starting up my Horus Heresy alpha legion (Part II deliverance)

So as i mentioned in the previous post. I had tried a BUNCH of  different ways of doing the Forgeworld recipe but i only got half hatched solutions that were,simply put, not up to scratch at all. Even to my standards.

Alas a wise Raven came to me rescue....No. Not hugin or munin, but my actual mate that goes by the moniker.

He runs a sweet Tau army with a cool camouflage patterned set of crisis suits, now the mere idea of CAMOUFLAGE is so ridiculously usefull and utilitarian, that it had to be invented by the renegade farsight enclaves. Which is what he rolls, what does that entail? Him blasting me with melta and plasma from all angles generally.

But still, enough bellyaching about the state of 40K. More bellyaching about my painting.

So basically my mate went, "hey, wanna borrow my airbrush for a session and see what we get?" Little did i know that the first free taste is what gets you addicted......

Now he has a Harder steenbeck infinity airbrush, with a matching compressor. Now, at the time i had no idea, but this is a really.really. REALLY good airbrush, only as good as the use. of course. But good for beginners and excellent for experienced users in regards to the details you can get.

Now to AGAIN reiterate. This is the formula i went after


1. AIRBRUSH WITH THINNED LEAD BELCHER/ IRON BREAKER (50/50 MIX) 
2. AIRBRUSH FROM TOP OF MODEL WITH THINNED RUNFANG STEEL 
3. MIX A LITTLE TAMIYA CLEAR GREEN WITH TAMIYA CLEAR BLUE (25/75 MIX) AND AIRBRUSH OVER THE MODEL IN 2 COATS 
4. AIRBRUSH ARMOUR PANELS WITH TAMIYA CLEAR BLUE. BLENDING FROM MIDDLE OF FIGURE DOWN, SO THE STRONGEST BLUE COLOUR IS AT THE BOTTOM OF THE PANNELS 
5. AIRBRUSH FROM THE MIDDLE UPWARDS WITH TAMIYA CLEAR GREEN 
6. USING AN AIRBRUSH BLEND A HIGHLIGHT ON THE HIGHEST PANNELS (HEAD, SHOULDER PADS, TOP OF BACKPACK) WITH RUNEFANG STEEL WITH A TINY AMOUNT OF LOTHERN BLUE, EXTREMELY THINNED DOWN. 
7. APPLY THINNED COAT OF TAMIYA CLEAR BLUE OVER THE HIGHLIGHT AND BLEND INTO THE SURROUNDING AREA. 
8. USING A BLUE GLAZE, DRAG DOWN THE WHOLE MODEL ALLOWING IT TO SETTLE IN THE DEEPEST AREAS. 
9. SILVER – BASECOAT WITH LEADBELCHER 
10. WASH WITH NULN OIL 
11. HIGHLIGHT WITH LEADBELCHER IN STRIKING MOTIONS TO CREATED CHIPPED AND WEATHER APPEARANCE 
12. HIGHLIGHT WITH IRONBREAKER

I actually printed it out and had it laminated next to me. 

basing (step 0) 

So started by basing all the ones i was going do black, using Vallejo standard black primer. 

After this i ran into a snag, i had failed to notice that my one bottle of leadbelcher had dried out. Oh shit son! My friend, full of calm and wisdom suggested i move away a bit from being GW centric, and broaden my horizons...live a little.....

Falling for his husky tone and slender frame i quickly agreed. Where was the harm, really? 

Nowhere actually, i went with testing the Vallejo metallic range. And it was good. So good. 

sin in a bottle. Albeit a new sort of bottle for me. 

Step 1 

Having replaced the leadbelcher iron breaker step for a different selection colours ( thinned chainmail and metallic black) i moved on with priming approximately 30 Alpha legionairres, HQ's and two rapiers platsforms. 

Now, had i been more experienced i would have realized that this step alone would take more than an hour (my estimation) but still. lessons learned 'n all dat' zog 

Step 2 

moving on from the first step, i gave all models a slight shine of silver from overhead. To get a nice shine of depth. 

I was kidding with my friend that if i had done iron warriors i'd be half done now. Then i cried a bit in pitying myself. 

After being slapped into a semblance of normality,i moved on. 

Step 3 

So this is actually what the mix should look like in Step 3. 25% tamiya clear green 75% tamiya clear blue

After using my friends mixer bottles and thinner, i concocted the base mix of colours, and started doing models.

As is readily visible, after the first coat, you will have some transparency to the metall underbase. Which is why it is so important to be neither to silvery,nor to leadlike  

just plugging some despoilers here. 

Afte doing the first overpass you are going to want to let it dry off. Here is a good tip again. 

CLEAN YOUR AIRBRUSH INBETWEEN COATS. 

The alcohol based paint CAN and WILL deteriorate the metal, and rubber parts of the brush proper. So you will want to do a quick clean between each "drying phase" or not. It is up to anyone of greater experience to chose themselves. 

So the following pictures are after the second coat in step 3 

The second layer gives a nice depth, and really brings out all the details in the Alpha legion parts used on this model.

 This is actually one of the first models that i tried to do by brush. I simply sprayed it with a light step 1 and onwards.

bringing out the model on the left, as we will follow him on the rest of this little trip i am sketching out. 

And this is as far as i got for my 30+ modells in the seven or so hours that i i borrowed my friends airbrush, overall i was really glad to give it a swing. And the result finally lived up to my expectations.

But i was not nearly finished, was i?